搜索资源列表
uart.zip
- uart串口通信程序，用状态机实现的；测试通过，并且实践过,uart
fpga-dm9000a
- 一个项目工程，硬件包含XINLINX FPGA，配置FLASH，串口，SDRAM,与以太网芯片DM9000A，实现数据采集，以太网传输，电路验证完全正确，请放心使用，SPARTAN 3E 的BGA引脚320个，不容易布板，可以参考使用的。要FPGA实现网络通信也可以参考电路，B因为产品升级了所以公开原来的电路的。 -A project engineering, hardware contains XINLINX FPGA, configuration FLASH, serial port, SD
UART
- 利用FPGA接受232芯片的串口数据，可以与PC进行串口通信-FPGA chip using the serial data received 232, serial communication with PC
uart
- 采用VHDL语言编写的串口驱动程序，已调试通过，能够实现同PC机的数据传输，可读性好，可移植性好-VHDL language using the serial driver has been debugged, to achieve the same PC, the data transmission, readable and portable
DE0_RS232
- Altera公司的多媒体开发板DE0上实现的串口例程-Altera' s multimedia development board to achieve the serial routines DE0
UART
- 自己实用Verilog编写的UART程序，1位开始位，8位数据位，1位停止位，本测试程序配置完管脚后，实用串口大师发送数据，则返回数据为发送数据+1-Verilog prepared their own UART practical procedures to start a bit, 8 data bits, 1 stop bit, the test procedure End pin configuration, the utility serial Master to send data,
UART
- 语言：verilog语言 功能：通过串口控制模块，实现FPGA与串口 通信。 仿真环境：modelsim 综合环境：quartus -Language: verilog language function: through the serial port control module, FPGA and serial communication. Simulation Environment: modelsim integrated environment: quartu
FPGAuartdebug
- FPGA串口界面调试程序,用VHDL语言实现-FPGA serial debugger interface, using VHDL language implementation
CPLD
- ad采集的小模块，实现串口转并口的功能，串口是SPI的接口-ad collector modoudle ad ad ad ad ad da da da da shuzi moni moni shuzi caiji caiji caiji caiji caiji caiji caiji
chuankou
- 串口VHDL实现 -Serial Serial VHDL realization of VHDL
UART
- 串口实验，很好用，我还有verilog HDL VHDL CPLD EPM1270 源代码-Serial experiments, very good, and I still have the source code verilog HDLVHDL CPLDEPM1270
sclock
- FPGA EP2C5Q288C8 串口原码,测试OK 打开即用.-FPGA EP2C5Q288C8 the original serial code, test that is used to open OK.
SPI-Collect
- 一个spi串口 希望大家能用上 -Spi serial a hope that we can use on
71477212NiosII_uart
- 串口sopc uart实现串口功能，包含帧的开始字节，命令字节-Serial sopc uart serial implementation features, including frame start byte, command byte
DP_RAM_lab
- 用SmartGen 生成一个2k*8 Dual Port RAM，并通过串口发送数据初始化RAM。然后通过串口返回到上位机的串口调试程序显示。-SmartGen generated using a 2k* 8 Dual Port RAM, and sending data through the serial port to initialize RAM. And back through the serial port to the PC serial port debugger displ
xapp345_vhdl
- adc转换功能的vhdl源码，其中包含adc_interface 和转换还包含串口输出-adc tranfer
VHDL
- 可用于FPGA的用VHDL语言写的关于串口通讯的源代码-FPGA can be used in the VHDL language used on the source code for serial communication
uart_controler_0622
- 自己设计的串口数据格式转换模块，转换格式为8位——32位，用户可自行修改。-Design their own serial data format conversion module, the conversion format for 8- 32 spaces, users can modify their own.
uart_module
- 实现精简的uart串口,格式起始位+8bit数据位+可配置的奇偶校验位+停止位-implement a smart UART interface
signal
- verilog写的串口控制信号发生器，能通过用串口控制产生正弦波方波等信号-written in verilog serial control signal generator, can be generated using serial control, such as sine wave square wave signals